Does anyone know if the losi 454 one way bearing is the same as the lrp 28? Or where can i get a lrp 28 owb? I went to my local hobby store n they had a mach 26 owb i thought it was the same looks almost identical but its a tiny bit taller n wouldnt let the back plate bolt all the way in was...
I'm over my picco .28 team turbo motor eating the driveline in my revo all the time, I'm also over bump start engines. Picco is getting tired, so it's time for something with less stomp & a pull start.
I've got an LRP ZR.30 that's in ok condition, I can most likley pinch the crank & pull...
so i was out on the last brissy bash and my BB revo decided to stop suddenly.
so i have finally got it pulled apart....
i have found the problem (the one i was hoping), the main bearing has crapped it big time... see below.
luckily when it decided to let go one of the balls got...
Well I have acquired a new/used MT & finally got my hands on what I have wanted for a long time! Team Associated Monster GT 4.60 with a few hopups.
This will be my only primary nitro to drop $ into until I get my busted and bent up MAXX goin.
Here are some pics
I am curious to...
I just bought a new lrp ZR .32 for my Ofna 9.5 pro.. I have it mounted and the dry fit is very nice, unfortunately the old flywheel/clutch and nut from the old engine does not fit the lrp ZR 32. The spec page says the crankshaft is 14.0mm/10.0mm bore/ SG shaft/ triple turbo scoop.
What clutch...
Does anyone know of some clutch bell bearings that withstand the power of the engine? I'm using the traxxas ones right now and we race every week and I have to replace them after every night of racing
Okay guys I am lacking smarts in this category. I want to run an HPI flywheel and clutch setup on my LRP .30 on my race maxx. Will everything match up ok. Also was thinking about using HPI HD aluminum clutch shoes the ones used on the K5.9. What other clutch shoes does the RCNT community...
Here's my problem I start the engine no problem there but when it gets up to about 200 degrees it wants to sputter like its not getting fuel also when it's hot will not start again can't get a tune on it either it has to have rich settings like almost factory or it won't run I'm wandering if I...
I'm looking for a roto start backplate for a lrp .28 I've been looking but having trouble finding one. I picked up a savage xl and savage x ss today and the xl had a lrp on it but the backplate thats on it is really crappy looks like plastic to me. Pull start backplate looks much better can you...
I have a lrp z.28 spec 3 engine and I'm having trouble with tuning. It dies when giving it a little throttle. And seems to over idle after coming off full throttle.
Hi guys it's me again.
I bought a lrp 32, 2 months ago for my savage x I install it on my savage and I could not turn the engine on, with my little experience I realized that the carburetor wasn't pulling any fuel into the engine, so I thought it have to be a air leak a I started looking for...
How would the Ofna force .32 compare to the LRP engines in the same size. I found one for a pretty good price online. And are they an easy tune engine.
WOW a lot more power than the z.28 and faster. can't keep it on all fours at any speed even with the 18/38 gear setup. so I am going to try the 20t bell.
had a few problems with the ERCM pipe tho. had it rear mounted and the header got bent up so bad its pretty much unusable. so I side...
Okay I need some opinions here. I am putting a custom T maxx race setup. I am trying to decide between These LRP engines. The .32, .30, .28. Really looking, for some speed. Prob, going to send engine off to have some modding done to it.