picco

I'm looking for either a O.S. 18TM, O.S. V-Spec .21, or a .21 - .28 Picco engine (small or big block). I have TONS of Revo hop-ups, and spare parts that I would be willing to trade including a Tekno RC Brushless Conversion Kit. Send pics and the price shipped to 67110 at...

a couple months ago a meandered into my hobby shop and asked them if there was a way to get more power out of my t-maxx. They said of course, and put a shiny new picco .26 max in front of me, which i proceded to buy, take home, laugh about, and drool thinking about until i had it installed. then...

I was looking to upgrade my engine from a 4.6k to a.28 pico. I understand i should get another exhaust pipe and there are kits for roto starters as well. also what should i use for clutch bell shoes etc. I was thinking of just changing bearings in the clutch bell and using the stock setup. Also...

Hello New to this forum so sorry if this is in the wrong place........ I need some advice. I have a Revo with the standard 3.3, I replaced it with the Picco .26 and onfa mount with the higher flower traxxas exhaust (the chrome one) running the Spektrum DX3 with telemetry. Fuel is 25%...

i have a revo 3.3 with a picco red dot jl maxx and a set of 8 1/2 inch jumbo swap tires i was wondering what is the best clutch for me to be using? thank you

ok as the title says I'm considering upgrading my tmaxx 3.3 (4908 chassis) to either a os .21 or a picco .26. I'm trying to get some feedback on the differences and traits of each of them.... e.g. low end power or high end power, average lifespan (assuming good tunes each run), holding tunes...

Just looked online at a Picco .26 engine. According to the website, the .26 is a drop in replacement for the 2.5 TMaxx and the .26 puts out 2.5 HP. Has anyone used this motor or does anyone have any comments or ideas about this swap? Thanks.

I just got a new Picco .26 Maxx for my Revo. I ordered a few O.S. #8 Glow plugs for it when I bought it because they were recomended by the site that I purchased it from. I noticed that the thread depth of the O.S. glow plug is shorter than the Traxxas ones I have for my 3.3 motors. Does...

theresno adjustment on the motor mount i want the power but ithouht with the motor mountit was supose to fit right in how do u get the gear mesh right

I am using an EZ start system. I tried a known good one way bearing FROM A TRAXXAS, and a known good EZ start system. It is slipping / not turning the engine reliably. Is there a diferant one way bearing for the picco? The starter shaft doesn't look worn...... If its the...

Well guys, I've decided to sell it! If this sounds corny, it's cause it's my ad from craigslist.:D SOLD! Up for sale is a 1/10 scale Traxxas Revo that started life as a 3.3 monster truck and has been modified and customized into an awesome looking racer or basher. This truck is very fast...

i have a revo platinum with a picco .26 max motor in it. motor has new boca bearings ceramic bearings in it. truck has rpm arms all the way around, traxxas cvd's, alum knuckles, alum servo savor, and alum mid skid (between front and center skid) and your tx and rx and your ready to go! SOLD...

I just bought the .26 red dot for my Revo. I'm excited i hope I made the right decision. I assumed I would buy the picco revo mount but i read in another forum this it is junk and the best think is to buy the revo big block conversion kit? Thanks in advance for advice:)

I finaly got around to trying my "new" used revo. came with a used picco .26 on it. I had to replace the engine mount and the spur and bell gears. ( I have about $50 into this truck total LOL yes FIFTY) The engine was free spinning ( not seized) so I figured I would set the needles...

what are my rear exhaust pipe option for the Picco .26 amx/red dot? is the stock traxxas resonator pipe will do? Thanks

Looking for more power out of my revo, and am stuck on motor options. Looking for a good improvement. Driven these trucks for years from when the tmaxx first came out, I have experience driving so please keep the " keep driving it" comments to yourself, serious replies only please.

I got the truck used, and the engine isnt on there right at all. The gear mesh is SMASHED together. Its a 5309 revo, I AM USING a ofna51531 revo engine mount for the ofn51223 .26 picco max. I can't find anything bent or messed up.There just doesn't seem to be enough adjustment for...

i have a new 2.5maxx picco. never even mounted. for $189.00 tax $14.xx. only cashers check. i ll pay the shipping. [email protected]

YouTube - Losi 8ight 2.0 bashing. The Losi is defying being bashed until broken. It won't break. I hammer it, cane it, flip it, cartwheel it, bounce it off stuff, jam it's wheels with gravel, jams it's steering with gravel and all it does is idle impatiently while I clear them then...

hello all,, just wondering if the picco .28 will fit on savage xl ?/ it looks like carb on the .28 is on the wrong side,, can you flip it around ?/ I've been researching and seems like the picco .28 would be a good engine for the xl,, but just wanted to get some advice,,as i do not have much...