I have the rear RPM blue a-arms upper and lower and axle carriers for the traxxas t-maxx 3.3
I had these on my 4907 tmaxx but went with rpm tru-tracks...
$25 shipped takes em !!!
Is there a better axle carrier for the slayer? I just got my engine running good then I take it out but a axle carrier not even a tank into the run. Just replaced them new all the way around. I didn't know if they made a metal one or if they would do more damage than pulling the pivot ball...
just wondering if there is such a thing ...i got some 20mm losi hubs ..and i didnt know they were made for a bigger axle than what my revo has ....i was able to make some temporary ones until i find something stronger to make them out of ...basically it just needs to be a metal sleeve that...
These are now out for the XR10 but at $119.99 I think this one VP upgrade I will have to pass on unless I get it as a gift.
http://www.vanquishproducts.com/xr10-front-axle-to10.html
Also comes in silver
I notice that when I am going along my rear sits kind of low, but when a start up on a rock or obsticle, rear flattens out, shocks fully compress and my leafs damn near straight if not straight. What would do this and is this bad? I am not sure if my shocks are internally sprung but should they...
Got to sell some stuff to get a handfull of Lipos for my new SCT.
All items are NOT priced with shipping unless stated with cost below. Shipping will be determined on your wherabouts in this crazy world. Paypal ready & only scaler accesories & HIGH mAh 2S Lipos I would consider for trade...
Put the RPM A-Arms and Axle Carriers on a while back, I know you gotta leave the front axle carriers loose some so the wheels can turn but what about the back... Do you leave them a lil loose or tighten them ?
I have them loose now and it just doesn't seem right, But I wanted to ask first to...
so all my new parts showed up and i started installing the rpm tru trac and the front arms and axle carriers... i dont have it all together but i see 2 issues... 1st... why does my fronts not want to steer easy? did i tighten something too much? and do the screws from the pivot balls get screwed...
Ok, for some reason the drive shaft/axle that extends from the right side of the front differential seems to want to fall out of the wheel when I turn to the right... I thought it was b/c the axle was bent, so I replaced it and still having the problem.. I looked a little closer and it look like...
SOOOO...... I was looking thru my pile of parts and I have 2 tmaxx diffs. Then the though came to mind, what if I mounted axle tubes off of it at a slight downward angle, ran the shafts through the center. Could be an interesting start to a shafty crawler, I also have a stampede.....hmmmm
http://rpmrcproducts.com/products/traxxas/16th.htm#16thcarr
Traxxas Mini E-Revo w/ RPM Parts Installed
Axle Carriers for the Traxxas 1/16th Scale Mini E-Revo & Mini Slash
Blue Axle CarriersThere is very little that can be as frustrating on an R/C vehicle as slop in the suspension system...
robmob
Thread
axle
electric rc
monster truck
traxxas
traxxas e-revo
traxxas revo
--------------------------------------------------------------------------------
ok so I'm kind of new to this rc stuff and i just recently bought a T-maxx that is a 2.5 chassis but it has a 3.3 motor and resonator pipe and the chassis is aluminum but thats about it for aftermarket. But...
Well, I have a revo that was a slayer that came with OFNA 17mm adapters. After converting it to a revo and running larger MT wheels/tires it became fairly evident that since there is nothing but the threads of the axle supporting the end of the wheel hub that wear and slop soon develop.
This...
I'm not really into crawlers, well, not yet that is. But I need to tap some of your knowledge. I see crawlers that have straight axles, and I was wondering if those that handle high speeds. I have a project in mind, but I really can't go forward with it until I can work out a few details, this...