Search results

Yeah if your serious about it youll want to go lipo. Quicker response and they run the same all the time (You dont have the drop in voltage as u run) it wil cost a little for a charger and batts but in the end u will be satisfied. 2s is all u need, but if your esc will handel 3s WOW! Its up to U...

Did u break your motors in correctly! They should be broken in in water. To do it correctly check out the Western Pa crawelers site @ networkhobbies.com search electric motor breakin. The post is by Rock Crawler the president he takes u set by set on how to do it right. If your running lipos ...

Dont know. Its just a quick fix when u are in a bind. If u have to drill another hole sobe it. Its better than lookin @ it on the work bench wishin u could run it.

Your Pre load collars depend on how your truck sits. When it is at its normal stance (When you set it down on the table) the axles should set parallel w/ the ground. If thats good you are good. Make sure and check it after you run a few charges b/c it may start to sink as the suspension breaks...

No video but I went about 40ft on my lid do to Lift off @ about 50 55 mph. Luckly it stayed on its lid the hole way or it could have got expensive. WOW

If you are having problems finding front A arms for your 4x4use a rear off a 2wd. Cut the cross brace out fo the end closest to the hub carrier so it will clear are the c hub and drill behind it for 4/40 rod put the rod in with 2 nuts and bingo back into buisness. Hope this helps

I'm usine 70wt in front shocks and stock 50wt in rear. Also I'm usung 10000wt dif lube in front and back but I'm thinking about going up to 20000wt b/c I'm running 3s 5000mah lipos and a 16 tooth pinion and its scary Also u can try a pc of nitro gas tube inside your shock about 1/4 in that will...

I thought heat would become a problem with it. I am going to try cutting out two pieces of lexan running from the front shoch tower over to the nerf bars about 2in high. Bolting it to the chassi and seeing what that will do. Hopefully it will keep out some dirt etc. w/out producing too much...

Check hobbyking.com for your batteries they have a lot to choose from. It will take about 14 days to get them b/c they usually ship from Hong Kong. I just bought two Zippy 5000mha 3s 20c for my 4x4 slash performe great. Diff lube I would stary w/ 10000wt or 20000wt to calm down the torch stear...

Did heat become an issue for him. I heard it causes the electronics to get hot Fast due to the lack of air flow eventhough it is louvered on top. And unless you were a racer it probably wasn't a good idea to run one. Which I think translates to if you dont have a lot of $ to through in to...

Yea I heard that with a set of Calibers And Bows you can pretty much run any track around my area. But it seams like the Cals have to many pins some times and the Bows not enough. Just looking for an in betweener and thought the Gooses might be it Thanks for your info

I am caught between the bow and the goose. I like the goose better looks wise but the bows have been so reliable over the years. Any suggestions on witch to run, or is their a better on out their I dont know about. I'm running them on a 4x4 Slash. Feed back appreciated Thanks

Don't ask me why not, where did you come up with that, what do you care. Move on.

Why should I give money without knowing the facts? If I concider giving anyone or any org some money, i'd like to have an idea what is going on. :shrug:

Slowest guy in town, no poop?????? I simply asked why a place that appeared to be doing so well, with all those big boys, needed a fund raising effort to get over the hump, that is all for the 40th fiddlesticking time. :) I'm using the payphone in the parking lot. It uses a USB to get my...

Please please please, it's know.... :) For the final time, just for you....(everyone please understand, i'm not beating a dead horse. He asked for this AGAIN.) The site has 4 forum sponsors. Forum sponsorship costs $40 per month. $40 per month is $480 per year. $480 per year 4...

There is truth in your post. I need help. Goodnight. Nice edit tool boy.

Forget it, I guess the numbers I posted are too large for you to understand.

Everyone note to never correct Rolex when he is talking out of his ass on a subject he knows little about. Yes, when holding a bullshit session in a topic that has grown 8 pages in just over a hour or so, you quote what you are replying to. From now on we should all just post our...

You as in everyone. I'll use that "several big boys" quote for a long long time though. :cheers: You love every minute of it, coming back for more, over and over. :boxing: :)