Search results

I have Airtonics M8 tx and rx like new. 75mhz. Will include 8 MDP nimh batts, rx pack, and wall charger. Also, I have stock t maxx parts. chassis, suspension, shocks, tires, and more. I will also throw in Ez start w/ the batt. and a quick charger for it. I would like to get 125 for the...

RB S7 Globs of torque and power!!!!

have u tried Crispy Critters? i get pretty much all of my stuff from them and love their service. btw he's a UE vendor

Go on and grab 4 UE supershocks. If you're racing put some 60 wt in. Maybe I missed it, but you might want to check out U.E.'s support forum for more details.

Just got it today. I bought off ebay along w/ 2 standard servos and a high speed 94357 ( my throttle/brk ). Only problem I didn't get any instructions and this is my first computer radio. I have been able to figure some stuff out like exponential and epa, etc... But there is some fine...

For the rev. to engage it does have to be "idle'ed" way down. Just go FOC like said above. As far as running, how many galls you ran? Mine ran like crap until i got about 3/4-1 gall. in it. And finally found a good spot ( btw it liked 230 deg.) Each engine is diff. Try some diff. glow...

It's just a wall plug in type. Very basic, no readouts, or lights, just a basic charger. thanks for the advice

I just got my Nimh batts for my tx/rx today. These are my first rechargeables for my nitro truck. My question is, how long do I charge them? I have a overnight charger but, how long is overnight? roughly 6-8 hrs.?

You needed to have meshed the spur and clutch bell properly. Take a piece of plastic like a part came in. Fit b/t the two gears and then slide your engine over. Tighten motor mts. down. Pull plastic out from gears. Check and make sure they are not too tight. Thats what I do to check mesh.

If I was a beginner DO NOT buy used. Unless it's from someone you know personally who can show you the rc. Sometimes the items that are in "new" condition, are just cleaned up wore out junk. W/ that said. I bought a Tmaxx 2.5. If I were to do it again, I'd prob. try a Savage 25.

If everything is running fine, all you need to do is put w/e after run oil in your motor ( and "cycle" by turning) and thats it. Some bearings like one way might need special grease, but I can't really think of anything now. basically just kinda flush your motor out and thats it

from your name i'm guessing this is www.insidelineperformance.com if so, i'm planning to check out a race this wknd 21st

http://www.insidelineperformance.com just found and will be trying out. It's at Goldsboro.

I've got the reg. S7 w/ pullstart mod. It's awesome. Starts up w/ no problems. Best buy I've made so far.

Looks good man. It's tough for me to drive em when they are clean.

Anyone know of any offroad tracks in Raleigh area?

What is a GS storm or MGT. I have no LHS, everything is mail order. I'm also only r/c guy around here. About buying the parts, the ones I need are Unlimited Engineering parts. Gotta have the stronger stuff for the maxx.

I'm waiting on parts for my Supermaxx that won't be back in stock until 4-6 wks. (which usually means 8-12 wks). I have a almost new RB S7 I'm dying to put in a vehicle. I kinda want to buy a savage (or another vehicle) for w/e one r/c is broken down I have a back up. Should I buy a...

I've got 2 MIP's(for ext. chassis). send me email [email protected]

I'm looking for a 85' or 86' Honda 250R ATC (3 wheeler). I have a Tmaxx with: Supermaxx Chassis Supermaxx wide-trac RB concepts S7 w/ UE pullstart mod (only 1 quart ran, still breaking in) Supermaxx Shocks 4 shocks ( 80 wt. oil, black springs) MIP CVD Great Assembly 7075 bulks w/...